Announcement

Collapse
No announcement yet.

Ask an ebike technical question get an answer within 30 minutes or so.

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • DaHose
    replied
    Provided it can sit flush, and the shaft is the same diameter on both shocks, the bottom perch of the DNM should be fine to use. That is a not a moving, high tolerance part. Mind you that if the spring is "just barely" too small, it might end up sitting flush on your first big hit. It would be an adventure separating the spring from the bottom perch if that happens.

    Jose

    Leave a comment:


  • ThunderGatti
    replied
    Hi, I'm upgrading the rear shock on my 2020.5 Sur Ron X and need some help determining if my spring fits properly.

    I bought a used DVO Jade and added the 550lb DNM spring from Luna to it. It doesn't rattle or move around at all, but the bottom of the spring isn't perfectly flush due to the raised inner section of the lower ring. Is it ok to use it like this?

    Another option for me would be to flip it over so the bottom ring is upside down. Again, not sure if this is OK to do, but it appears more flush this way.

    The top ring is perfectly flush though, since it has no raised inner section (see side by side pic). DVO sells the the lower rings with the option to select the amount of stroke reduction (0, -2.5, -5, -7.5mm). Would selecting 0mm mean there would be no raised section?

    Alternatively, I could purchase a second top ring and just cut out a slot, which would make it fit perfectly. Getting a different 550lb spring is very difficult right now. I have a Ti spring specifically for the Jade on order, but it won't be here until the end of November. The only other option that I'm aware of is Fox, which won't be a perfect fit either. Since I'm essentially still a noob with this stuff, I was just hoping to get some guidance on how to make this work. Thanks.

    edit - one other idea: How about using the bottom ring from the DNM, since it's designed to fit the spring?
    Last edited by ThunderGatti; 1 week ago.

    Leave a comment:


  • paxtana
    commented on 's reply
    I would recommend to email support and make sure to include a picture

  • alosip
    replied
    This is a question about my x-1 enduro. My frame was squeaking so I took apart rear shock linkage to clean, grease and Locktite it.
    Now I need to put it back and I can’t remember if a “conical seal ring” goes conical side to the ball bearing or the other way around. I am not sure what this ring is called. It’s basically a thick washer with a grove on perimeter and an o-ring in it.
    thank you.

    Leave a comment:


  • paxtana
    commented on 's reply
    Most led readouts for ebike batts are not color changing, they usually just make the last led the color red so as the leds no longer light up, eventually you hit the button to show how many are lit up and it just shows the red one, which is meant to indicate time to head back. I don't know if that's the case on this specific battery but it probably is

  • alosip
    replied
    Is there a document about battery on X-1 enduro?
    My battery build-in indicator, when charged to 100%, always shows all led lights green except the top which is red. Is something wrong? Shouldn’t it be all green?

    Leave a comment:


  • Steampunk
    replied
    It says right there in the listing....
    $459 gets you battery
    + $30 gets a slow basic charger
    ...or... + $55 gets you a luna 3amp faster charger

    Leave a comment:


  • paxtana
    commented on 's reply
    It only comes with a charger if you select one of the optional chargers on the listing

  • paxtana
    commented on 's reply
    Follow this guide https://electricbike.com/forum/forum...ctrical-issues

  • SamGame_G
    replied
    Does anyone know if https://lunacycle.com/48v-panasonic-13-5ah-shark-pack/ comes with a charger or do i need to buy another one ,Thanks.

    Leave a comment:


  • Velodave
    replied
    I've experience a shut down @47 volts.it runs for 10 minutes then shuts off.

    Leave a comment:


  • paxtana
    commented on 's reply
    There are only a few bolts holding the motor in place. If you think it's coming from there, try tightening those three bolts

  • alosip
    replied
    My new X-1 makes a lot of creaking sounds when I pedal, especially with power assist. I already greased the top pivot of rear suspension shock. It didn't help much. It feels that sounds coming from the bottom bracket but I am not 100% sure. Any suggestions would be appreciated.

    Leave a comment:


  • dirt tan john
    replied
    Thank You ncmired, I just purchased the Connex 108.

    Leave a comment:


  • ncmired
    commented on 's reply
    Connex 108, and Sturmey Archer 1/8 sprockets.
Working...
X