Announcement

Collapse
No announcement yet.

Luna X-1 Enduro FS ebike MANUAL

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • jjdicecco
    commented on 's reply
    I went to that forum and when I click on the link for the wheel set it’s a blank page... would you be able to send me in the right direction for the carbon wheel set

  • huachinango
    replied
    Ok, I’ll keep that in mind. Seems like I’m waiting in a support queue now.

    I’m starting to think the quiet gear swap didn’t go well and that’s my issue. Here’s a video.
    Watch "Luna X1 problem" on Streamable.

    Leave a comment:


  • EL34
    replied
    Originally posted by huachinango View Post
    Took another look today. All the connectors are plugged in tightly. I took it for another ride and tried throttle only. The motor is spinning but not propelling the bike. I took it back home, raised the rear wheel, pegged the throttle. Just like I thought, motor runs but doesn’t move the wheel. Gotta call Luna now.

    The tech who called to help yesterday wasn’t actually a tech He talked me through how to erase the code (it didn’t clear, btw) then said he didn’t know what to do and told me to send another email to support (they haven’t responded yet.)
    If Tony from Luna responds to you, tell him to go get someone that knows what they are talking about.
    His replies are often completely wrong

    Gary is great and so are the bike techs at Luna that I have dealt with.

    Leave a comment:


  • mw195
    commented on 's reply
    I planned on taking my front up to 220mm, but got a 203mm instead (by accident). Figured might as well install it, but the new rotor has a very slight warp to it...not enough to bend out, but I cannot get rid of the scrapping. May go back to the stock 200mm SRAM rotor. Oh, the replacement was a Hope 2 pc floating disc that looks very nice but I just cannot get it to not rub. I intended to get the 220 rotor, and thought that was what i ordered, but the packing slip says 203 (I am guessing that when I selected Red carrier, since no Red220 are in stock, it defaulted to the 203mm. Figure, why not just mount it and when the 220 Red is available I can install that and move the 203 to the rear...But now i am thinking that it needs to go back.

  • huachinango
    replied
    Took another look today. All the connectors are plugged in tightly. I took it for another ride and tried throttle only. The motor is spinning but not propelling the bike. I took it back home, raised the rear wheel, pegged the throttle. Just like I thought, motor runs but doesn’t move the wheel. Gotta call Luna now.

    The tech who called to help yesterday wasn’t actually a tech He talked me through how to erase the code (it didn’t clear, btw) then said he didn’t know what to do and told me to send another email to support (they haven’t responded yet.)

    Leave a comment:


  • eskachig
    commented on 's reply
    I got one of those too :)

    But then I put a coil shock on, so I'm back to fighting for every gram.

  • EL34
    replied
    Originally posted by eskachig View Post
    Anyone looking to put their bike on the diet, the stock 800mm handlebar is a good place to start. It's 330g, pretty damn hefty. I replaced it with a 760mm carbon bar and it's literally half the weight. You'll need new grips too, I think the stock ones require the cutouts on the end of the bar and I've never seen a carbon one come like that.
    Go here
    https://electricbike.com/forum/forum...-other-x1-mods

    The wheel set alone dropped 5 pounds off my X1

    Leave a comment:


  • eskachig
    replied
    Anyone looking to put their bike on the diet, the stock 800mm handlebar is a good place to start. It's 330g, pretty damn hefty. I replaced it with a 760mm carbon bar and it's literally half the weight. You'll need new grips too, I think the stock ones require the cutouts on the end of the bar and I've never seen a carbon one come like that.

    Leave a comment:


  • eskachig
    commented on 's reply
    Yes, you can true a brake rotor. Eg,

    https://www.youtube.com/watch?v=SpRhigdK5ic

    Can't help you on the throttle, but the stock one certainly looks flimsy. I'm thinking about taking it off.

  • Frankie Brennan
    replied
    Hey all, I know the answer to this is somewhere in this thread but looking for a short cut. Took a big jump yesterday and went down pretty hard as the guy I was riding with went down right on the other side of the landing point. Bent my front brake disk and snapped off the thumb throttle. 2 questions, can I bend back a disk brake (even though I'm ready to upgrade to something bigger) and are there other throttle options available that work with this bike like a twist option? Thanks!

    Leave a comment:


  • EL34
    replied
    Originally posted by huachinango View Post
    Just got my girlfriend’s bike today, put it together and took it for a ride. It felt very under powered in all assist modes, I could only hit 15mph pedaling moderately hard in a high gear. Then the motor cut out and the display read Error 10. Gonna call Luna tomorrow but any ideas of what I should check now? It’s a Ludi with the quiet gear.
    I don't have Ludi and I never go above PAS 3, so something is wrong somewhere on your X1
    As was mentioned above, check all connections
    Take the plastic side panel off so you can see the motor connectors

    I show the motor connectors in this video
    https://youtu.be/7jHwGZLYPQ0

    Leave a comment:


  • Dave Mc Gregor
    replied
    It shouldn’t be under power. I’ve just used my PAS 5 on the techy trail. After that it’s too much power. Try to check the connection of your controller maybe something is loose. I had an issue like that and I found out that my connection is loose.

    Leave a comment:


  • K442
    replied
    You might double check that both wheels spin freely. My rear brake caliper was slightly misaligned on delivery and put some extra drag on the rear wheel. Definitely made the bike feel sluggish on the 'first ride', though I didn't go far enough to trip the 'overheat'. Once I noticed the caliper and re-adjusted to free the wheel, it made a notable difference. You also remembered the spacers on the front wheel, correct? If you're missing those, I think the front caliper could also rub.

    Leave a comment:


  • huachinango
    replied
    Just got my girlfriend’s bike today, put it together and took it for a ride. It felt very under powered in all assist modes, I could only hit 15mph pedaling moderately hard in a high gear. Then the motor cut out and the display read Error 10. Gonna call Luna tomorrow but any ideas of what I should check now? It’s a Ludi with the quiet gear.

    Leave a comment:


  • EL34
    replied
    Originally posted by steelersmb View Post
    I ordered and received my new 860C from AliExpress. It works but in the advanced menu, I can't edit the max speed. Can someone confirm that if you ordered it from Luna that you can edit the max speed and does it make a difference?
    Look right above your post

    Leave a comment:

Working...
X