No announcement yet.

DPC-18 Display documentation

This is a sticky topic.
  • Filter
  • Time
  • Show
Clear All
new posts

  • max_volt
    commented on 's reply
    Sebz kindly added red strikeouts. I wonder if eco/sport is for the new torque sensing models.

  • Scott S
    Just to be aware that the manual shows a default listing on the settings page where you can supposedly select eco or sport modes but this is not correct. That spot is now for selecting how many pas levels you want to be able to select via the display and display controller.
    A updated manual would be nice!

    Leave a comment:

  • Sebz
    commented on 's reply
    It is nice, and many are using it now... but it just came out a few weeks ago. I'm using it for sure!

  • Sebz
    commented on 's reply
    Thx Max-volt! I uploaded it on the top and edited it for the BSBHD/02 motors.
    Last edited by Sebz; 10-10-2017, 05:38 PM.

  • max_volt
    User Manual!AiO5B0KENXx-iRHu7sHzbwoBXFVt

    Leave a comment:

  • Scott S
    Is anyone using this display yet? Looks pretty good to me

    Leave a comment:

  • Sebz
    started a topic DPC-18 Display documentation

    DPC-18 Display documentation

    Luna DPC-18 color Display

    Click image for larger version  Name:	Main_PIcture__39755.1503343001.1280.1280.jpg Views:	1 Size:	228.6 KB ID:	45577

    Display Features:
    • Full Color Display
    • Automatic Night Mode (with customizable light sensitivity)
    • Choice of Percentage or Voltage display for Battery (goes up to 60V)
    • USB Charger
    • Accurate battery gauge
    • Watt OR Amp Display to gauge how much you are pulling
    • Clock
    • Password Lock (only locks the screen, motor will still work)
    • Error code list and memory
    • Waterproof
    • No more advanced menu, simpler interface.
    • New control pad

    Why upgrade?
    • It's well made, brackets are sturdier and will fit over wider/bigger MTB stems.
    • Looks better too, easier to the eyes.
    • Waterproof, DPC-14 was barely rainproof.
    • Higher visibility compared to the DPC-14 and has auto nigh mode.
    • No more advanced menus with passwords, better interface.
    • VOLTAGE GOES UP TO 60V! finally a accurate voltage meter.

    Video walkthrough :

    • 92mm x 57mm
    • compatible from 22mm to 32mm handle bars (includes rubber spacers)
    • 3.2 inch diagonal screen
    • Glossy plastic screen
    • Waterproof IP65 (protected against small water jets, USB cap on)
    • USB Charger 5V 500ma MAX, not recommended to power head lamps
    Click image for larger version  Name:	TECH_SHEET__74320.1503103937.550.550.jpg Views:	1 Size:	115.3 KB ID:	45576

    How to use it:
    • Hold the power button for 2 sec to power up, hold for 2 sec to power down
    • Hold the headlamp button to force night mode
    • Hold the "-" button for walk mode (motor will run very slowly to help you walk)
    • Use the "+" and "-" to select the PAS setting (can be set 0-3, 0-5 or 0-9 in settings)
    • Press the "i" button to cycle from ODO, TRIP, MAX speed, AVG speed, TIME.
    • Double press the "i" to access the settings.
    • Set speed limit in display above 30MPH if you want display to show watt gauge higher than 750w
    Click image for larger version  Name:	DSC09977__72322.1503103939.1280.1280.jpg Views:	1 Size:	433.6 KB ID:	45588

    Main screen:
    Click image for larger version  Name:	LUNA_DPC18__08124.1503439684.1280.1280.jpg Views:	1 Size:	261.2 KB ID:	45581

    Settings :

    Double press the "i" to access the settings. Once in the menu you will see display and information,

    Information tab:
    To see stored error codes and battery information (NOT USED)

    Display tab:
    You will get this, move up and down using the "+" & "-" and select with the "i", then when highlighted change it with the "+"or "-", confirm your selection with the "i" button again.
    Click image for larger version  Name:	Main_Menu_Settings_copy__60824.1503439571.1280.1280-2.jpg Views:	1 Size:	209.7 KB ID:	45589


    If you are using this LCD with a 52V battery the fuel gauge and the % level will not be accurate at all, they will both show full till you have 30-40% left. This can play trick with you, can make you think you are charged when you are not or can make you think the battery is defective.

    So please set the display to SOC voltage and not percentage. Check our voltage charts here if you are unfamiliar with voltage levels: CLICK HERE

    • Even though it's IP65 rated, we do not recommend using a garden hose or pressure washer directly on the LCD.
    • The display is not waterproof if a USB wire is plugged in.
    • It's only capable of suppling 500ma (or 0.5a) so do not use it to power anything that requires more. No warranty on the USB port if used incorrectly.
    • Do not trust the Password lock down, I could actually use the throttle while it's locked.
    • The range fonction and any other battery info related fonctions will require a special BMS that is not available.
    • Does not work with Bafang Ultra. For Ultra, you need a different display specially built for it.
    • Use the voltage mode instead of the %, it will be more accurate, you can use our charts here to guide you :CLICK HERE

    Trouble shooting:

    Error codes :
    Dead LCD:
    Random issues:

    Last edited by paxtana; 04-14-2021, 07:31 PM.